What is a Brass Gate Valve?

A Brass Gate Valve is a standard gate valve, which can be used for a variety of applications, within fuel and water installations, and are suitable for use with diesel, oil and water. These brass gate valves are designed for starting/shutting off flow,

Are suitable for both above-ground and underground installation. You may better choose the correct lasting one for underground installations to avoid high replacement costs caused by digging and putting out the pipes.

Gate valves are designed for fully open or fully closed service. They are installed in pipelines as isolating valves, and should not be used as control or regulating valves. Operation of a gate valve is performed doing an either clockwise to close (CTC) or clockwise to open (CTO) rotating motion of the stem. When operating the valve stem, the gate moves up- or downwards on the threaded part of the stem.

Gate valves are often used when minimum pressure loss and a free bore is needed. When fully open, a typical gate valve has no obstruction in the flow path resulting in a very low pressure loss, and this design makes it possible to use a pipe-cleaning pig. A gate valve is a multiturn valve meaning that the operation of the valve is done by means of a threaded stem. As the valve has to turn multiple times to go from open to closed position, the slow operation also prevents water hammer effects.

Gate valves can be used for a vast number of fluids:

  • Potable water, wastewater and neutral liquids: temperature between -20 and +70 °C, maximum 5 m/s flow velocity and up to 16 bar differential pressure. 
  • Gas: temperature between -20 and +60 °C, maximum 20 m/s flow velocity and up to 16 bar differential pressure.

See a catalog of some of our valves: HERE

Parallel vs wedge-shaped gate valves

Gate valves can be divided into two main types: Parallel and wedge-shaped. The parallel gate valves use a flat gate between two parallel seats, and a popular type is the knife gate valve designed with a sharp edge on the bottom of the gate. The wedge-shaped gate valves use two inclined seats and a slightly mismatched inclined gate.

Most of brass gate valves are of the solid wedge-shaped design, but we also offer knife gate valves for wastewater treatment and parallel slide valves for gas supply.

Metal seated vs resilient seated gate valves

Before the resilient seated gate valve was introduced to the market, gate valves with a metal seated wedge were widely used. The conical wedge design and angular sealing devices of a metal seated wedge require a depression in the valve bottom to ensure a tight closure. Herewith, sand and pebbles are embedded in the bore. The pipe system will never be completely free from impurities regardless of how thoroughly the pipe is flushed upon installation or repair. Thus any metal wedge will eventually lose its ability to be drop-tight. 

A resilient seated gate valve has a plain valve bottom allowing free passage for sand and pebbles in the valve. If impurities pass as the valve closes, the rubber surface will close around the impurities while the valve is closed. A high-quality rubber compound absorbs the impurities as the valve closes, and the impurities will be flushed away when the valve is opened again. The rubber surface will regain its original shape securing a drop-tight sealing. 

The vast majority of brass gate valves are resilient seated, however metal seated gate valves are still requested in some markets, so they are still part of our range for water supply and wastewater treatment.

Gate valves with rising vs non-rising stem design

Rising stems are fixed to the gate and they rise and lower together as the valve is operated, providing a visual indication of the valve position and making it possible to grease the stem. A nut rotates around the threaded stem and moves it. This type is only suitable for above-ground installation. 

Non-rising stems are threaded into the gate, and rotate with the wedge rising and lowering inside the valve. They take up less vertical space since the stem is kept within the valve body. Valves  with a factory-mounted indicator on the upper end of the stem to indicate the valve position. Gate valves with non-rising stems are suitable for both above-ground and underground installations.

What is a brass gate valve with by-pass?

By-pass valves are generally used for three basic reasons:

  • To allow the pipeline differential pressure to be balanced, lowering the torque requirement of the valve and permit one-man operation
  • With the main valve closed and the by-pass open, a continual flow is allowed, avoiding possible stagnation
  • Delayed filling of pipelines

Other Kind of Valves

Gate Valve Parts

Here you can see the main parts of the gate valve. The disk of a gate valve is also known as a wedge.

Gate Valve Parts
Image- Trouvay & Cauvin from hardhatengineer.com

What types of Gate Valves exist?

There are three ways to classify the gate valve.

  1. Types of Disk
    1. Solid taper wedge
    2. Flexible wedge
    3. Split wedge or Parallel disks Valve
  2. Types of Body Bonnet Joint
    1. Screwed Bonnet
    2. Bolted-Bonnet
    3. Welded-Bonnet
    4. Pressure-Seal Bonnet
  3. Types of Stem movement
    1. Rising Stem or OS & Y Type (Outside Stem and Screw Type)
    2. Non-rising Stem type



Click one of our contacts below to chat on WhatsApp

× Whatsapp Here